Looking for:
Hunter fan installation manual
Make sure the ground wire is facing out of the large opening of the ceiling bracket. Secure the motor to the ceiling bracket with two locking screws. NOTE: This is the process for installing traditional-style low profile ceiling fans. However, we have two different installation styles for low profile fans in addition to this process that are different.
If your low profile fan model does not have the square hanging ball, look at your installation manual for specific instructions.
To install your ceiling fan on an angled ceiling, you will need to purchase a longer downrod sold separately and, depending on the angle of the ceiling and your fan type, you may also need a ceiling fan angled mount adapter.
First, make sure your ceiling fan model is compatible with being installed on angled ceilings. Assuming your fan is compatible with angled ceilings, determine the equipment you need for an angle mount ceiling fan. This angled ceiling mount replaces the canopy. You cannot install a remote control in the Original Angled Ceiling Mount because of the tight spacing.
For installations with a control on an angled ceiling, consult an electrician. This system is used in conjunction with the hanging system supplied with your ceiling fan. Hunter accessory and canopy mounted controls can still be installed within your fan supplied hanging system. For angled ceilings steeper than degrees, contact an electrician for a customized mounting fixture. An extension downrod is needed when installing your ceiling fan on a sloped ceiling. When choosing your downrod length, keep in mind that your ceiling fan needs to be 30 inches away from the wall and other objects and the fan blades must be 7 feet or more from the floor.
With the proper mounting bracket and downrod, follow the above directions from STEP 2 Install the ceiling fan mounting bracket as well as the subsequent instructions for downrod fans to complete the installation.
Slightly tug on the wire to make sure none of the wires are loose. Pull chain ceiling fans do not come with a remote receiver of any type. For ceiling fans without a remote receiver, follow these steps to wire your fan. Connect the white grounded wire from the ceiling to the white wire from the fan. Connect the black wire ungrounded from the ceiling to the black and the blue wires from the fan. Connect the black ungrounded wire from the ceiling to the black wire from the fan.
Connect the second ungrounded light wire from the ceiling to the blue wire from the fan. Hunter ceiling fans with preinstalled remote receivers have the receiver built into the ceiling fan body at the factory. Our engineers innovated this technology to help make wiring a ceiling fan simpler.
The remote control cradles can be attached to the wall. You can dock the remotes into the cradles to use them like a switch on the wall, or remove the controls from the cradle and use them as handheld remotes. The light switch powering the ceiling fan will likely be a single or a dual wall switch.
Cap the blue wire from the fan. You will not need it for single switch wiring. If you have a dual wall switch, the steps for connecting the wires with a wire nut will be similar to the above steps. The only difference is instead of capping the end of the blue wire in step 4, you’ll use a wire nut to connect the second ungrounded light wire from the ceiling to the blue wire from the fan.
Most Hunter ceiling fans come equipped with either a preinstalled or separate remote receiver. If you’re wondering how to wire a ceiling fan with a separate remote receiver, use the wire nuts to:. Connect the black ungrounded wire from the ceiling to the black wire from the receiver.
Connect the white grounded wire from the ceiling to both the white wire from the receiver and the white wire from the fan. Connect the yellow wire from the receiver to the black wire from the fan. Connect the blue wire from the receiver to the blue wire from the fan.
If you’re installing a ceiling fan that requires a downrod, you’ll need to finish installing the canopy. If you’re installing a low profile ceiling fan, you’ll need to finish installing the motor housing.
Tuck the wires and wire nuts into the junction box. Lift the canopy into place, making sure the triangular openings and screw holes are aligned. Using a screwdriver, insert and securely tighten the canopy screws. A magnetic screwdriver will give you more visibility when securing the canopy. Raise the motor housing up until it’s correctly positioned over the motor and ceiling brackets.
Rotate the motor housing until the screw holes are aligned with the holes on the bracket. The indentation inside the housing should lock into place with the notch inside the ceiling bracket. Hold the motor housing in place. Use a screwdriver to insert and tightly secure the four motor housing screws. Your Hunter fan comes with the necessary parts you’ll need to install the blades.
There are three common blade installation methods for Hunter ceiling fans:. Insert the grommets into each hole at the end of the blades. Use the respective screws to attach each blade to the blade irons. Position the blade irons with the motor, making sure all screw holes are properly aligned. Lightly hand-tighten the screws, then use a screwdriver to securely tighten the screws. Insert the blades into the openings and align the hole openings in the blades with the blade irons.
Attach each blade to a blade iron using the three provided blade washers and blade assembly screws. Make sure the screws are secured tightly. Align the three blade holes with the three blade iron posts. Squeeze the blade and the blade iron post together. Note that the flared tops of the blade iron posts will be fully visible above the blade when properly assembled. To assemble a fan with a lighting kit, first identify if your fan has a Quick Connect feature by examining the switch housing.
Hunter Quick Connect fans have a distinct locking mechanism located on the switch housing. These fans also have a ring that surrounds the switch housing in the middle.
Hunter fans without Quick Connect technology do not have either feature. Before beginning, remove the cardboard plug guard. Connect the fan and light fixture plugs together. Make sure to align the colored markings on the connectors. Push the connectors and the extra wire into the hole located at the top of the light fixture. Carefully connect the light fixture to the bottom of the fan.
Make sure the holes on the mounting ring at the top of the fixture are aligned with the spaces in the mounting bracket on the bottom of the fan. While holding the body of the fan still, turn the light fixture clockwise to engage the locking pin.
Listen for a clicking sound to verify that the locking pin is securely in place. Remove the socket rings so you can install the light glass. After installing the glass, reinstall the light rings into the sockets. Use the socket ring glass tool that came with your fan to turn the light rings clockwise until they’re tightened. Choose any two holes in the switch housing mounting plate to screw two of the housing assembly screws halfway. Feed the wire connector through the center of the upper switch housing.
Wrap the keyhole slots around the screws then twist counterclockwise. Use a screwdriver to install the third screw then tighten the remaining two screws.
Partially install two of the switch housing screws by halfway. Connect the upper and lower switch housing together using the plug connectors, making sure to line up the colored markings. Locate the notches in the sides of the lower switch housing and align them with the screws located on the upper switch housing. Lock the switch housing into place by twisting the lower portion clockwise. Using a screwdriver, install the third housing screw. Tighten all the screws. To install the light shades, first, loosen the thumbscrews.
Then, lift each shade to the light fixture and insert and tighten each thumbscrew. Connect the pull chain pendants to the appropriate short chains coming from the switch housing. Connect the fan and light fixture connectors. Make sure you line up the colored markings on the connectors. Secure the connectors by pushing the connectors and extra wire into the hole located at the top of the light fixture. This step will ensure that the fan and light fixture are successfully mounted.
Carefully lift the light fixture and position it at the bottom of the fan. Make sure the holes on the mounting ring located on the top of the light fixture are aligned with the spaces in the mounting bracket located on the bottom. Listen for the clicking sound to verify the connection is secure. Lift the globe and use the provided three thumb screws to attach it to the light fixture. Tighten the thumbscrews by hand. Install the provided bulb into the light socket.
Feed the fan pull chain through the hole at the bottom of the light kit. Install the light bulbs into each of the sockets. Position both the globe and globe keeper against the metal plate, keeping them flush. Feed the light pull chain through the hole located in the center of the finial cap.
Then, feed the fan pull chain through the hole located in the side of the cap. Feed only the light pull chain through the finial. Attach the finial to the threaded rod and tighten by hand.
Attach the short chains coming from the switch housing to the appropriate pull chain pendants. Not all fans have the option to be installed without light kit.
First, you need to determine if your fan model can be installed without a light kit. Fans with lights integrated into the body of the fan typically cannot be installed without the light, except for a limited number of models. Fans with arm or bowl light kits may be able to have the light kit removed and a no light cap installed.
How do I install my fan without the light kit? A no-light cap covers the portion of the fan where a light kit would normally be installed. If you’d rather use a no-light cap instead of a light kit and your fan model is compatible, use these steps to properly install it. Remove the two screws on the light kit that connect the light kit to the lower switch housing. Disconnect the blue and white wires inside the light kit and lower switch housing. To safely cap off wires not being used, install the dummy terminal included with the light cap.
Attach the terminal to the ends of each wire located in the lower switch housing. Use a Phillips head screwdriver to install the switch housing cap with the two switch housing screws you previously removed earlier. Connect the lower and upper switch housing with the connectors. Make sure you align the colored markings on the connectors. Carefully lift the switch housing and position it at the bottom of the fan.
Position the holes on the mounting ring located at the top of the switch housing with the spaces in the mounting bracket located on the bottom of the fan. While holding the body of the fan as still as possible, engage the locking pin by turning the light fixture clockwise.
Listen for a clicking sound to verify the connection is secure. Hunter offers a variety of ceiling fan controls that make it simple to control your fan and light. Most handheld remotes and wall controls come pre-paired to the ceiling fan. Handheld remotes let you conveniently control your fan’s features. Follow these steps to use your handheld ceiling fan remote:. Install the included battery into the back of the remote.
To turn the fan on and off, simply press the fan button. To change the direction of the fan, press and hold the fan button. To turn the ceiling fan light on and off, press the light button. Press and hold the arrow buttons to enable the dimmable ceiling fan light options.
Hold the light button down to dim the ceiling fan light. Wall controls are installed at the wall switch, making it easy to remember where your ceiling fan control is located. Follow these steps to use your wall control. Simply press the fan button to turn the fan on and off. The parts guide is extremely useful when you have broken or lost a part that goes with your fan, and now require a replacement. For instance, say you lost your remote.
Or, you dropped the glass globe and that is now broken. The parts guide will have a physical listing of said parts, so you can find a replacement part number in the parts guide. Once you have the part number you need, take a look and see if you can find the part on our website. If you cannot find the part, try calling a local Home Depot or browsing through their store or online website. With the part number in hand, getting support is a lot easier. Without the part number you will have a very tough time figuring out which part to replace on the fan.
The installation guide is for — you guessed it — installing your Hunter fan. Locating the relevant installation guide for your particular model is extremely helpful if having trouble installing your fan. With Hunter fans that have an attachable light kit, these manuals may guide you on how to install your Hunter fan with or without the light kit. Also included may be instructions on how to flush mount, how to install the fan blades, how to install the motor housing, how to wire the ceiling fan and more.
An installation guide will take you from the point A to the point Z. Hunter Parts Guide — this parts guide will help you to figure out which part you need when you need a Hunter replacement part.
https://aeroindia.net/hh1f
https://shaikhsr.xyz/50bw
http://siminsaz.ir/17z
http://runwayfashion.in/5su
http://whatsgold.app/5n9h
https://egyconnects.com/802b
http://leeb-balkone.de/75se
https://cortinajesaurora.cl/6jv1
https://nutritionwize.com/zden
https://asecus.ch/k8e
http://sipaling.cerdas.co.id/2eml
https://dmmart-store.my.id/ofh
https://littletreasurethrift.org/wlp
https://hekimconteneur.com/0ak8
Ceiling Fan Parts & Manuals | Hunter Fan
This instruction manual contains complete instructions for installing and operating your fan. We are proud of our work and appreciate the opportunity to supply. At Hunter, we strive to make ceiling fan repairs, installation, and upgrades easy. Explore our helpful resources for ceiling fan parts and manuals.
https://dpskolar.org/q692
https://lalordoflocks.com/pymh
http://drrajguruhaircareclinic.com/i6v
http://miraclecbd.store/5×2
http://rothenstein.de/ljis
https://bplp-aintemouchent.dz/gc4u
http://vivinavijesh.org/a1c
http://couponthemes.net/jjol
http://sydcar.com/8qzn
http://farrowcontrra.co.uk/rt6
https://kansascitylordoflocks.com/qzy5
http://ownit.nu/nnx
https://rhino-roids.com/7rg
http://diabetesandthyroidcarecentre.com/fsxk
Hunter Ceiling Fan Manuals & User’s Guides – Hunter Ceiling Fans
https://ownit.nu/c2j2
http://nauendorff.de/81oi
https://smarttools.de/s7y
http://maamanashaengineering.com/b882
http://qushoys.my.id/a4g
https://net.co.au/ye7
http://recoveryservicedubai.com/x0a
http://localssushi.com/gs8
http://spam.8pm.de/y30e
http://ttei.edu.bd/m95
https://smartdigitalkards.com/7exq
https://damiolanrewaju.com/lo4
https://chatte.fr/k1i
https://pioli.it/i2a
When installing on an angled ceiling, measure the ceiling’s angle. Not all fans have the option to be installed without light kit. Hunter Quick Connect fans have a distinct locking mechanism located on the switch housing. Most Hunter ceiling fans come equipped with either a preinstalled or separate remote receiver. Press and hold the arrow buttons to enable the dimmable ceiling fan light options.